since 1956 - celebrating our 56th year!
Thermal Management for Enclosures
Call Today! (800) 321-KOOL
Made in the USA
 
Refresh browser to display menu
 

Packaged Fans Accessories and Options

STANDARD STAINLESS STEEL GRILLES: These attractive stainless steel grilles are made of mirror-finish stainless steel and are identical to those on Kooltronic Packaged Blowers. All are 19-inch [482.6mm] wide. They are 65% open and comply with OSHA and UL safety standards.

GRILLE ASSEMBLIES: These assemblies are perfect for venting applications on the enclosure. These attractive grilles are made of mirror-finish stainless steel and are identical to those furnished on Kooltronic Packaged Blowers. All are 19-inch [482.6mm] wide. They are 65% open and comply with OSHA and UL safety standards, and include knurled captive fasteners for easy attachment and removal.

FILTER-GRILLE ASSEMBLIES: To provide a filtered air intake in applications where the enclosure is being exhausted, each Kooltronic Filter-Grille Assembly consists of a Grille Assembly, filter and two EIA-notched brackets. By loosening the captive thumbnuts, the permanent filter is instantly available for cleaning.

Model  
Grille
 Assemblies
Filter-Grille
 Assemblies
Height
KPG350-19 KFG350-19
3.50 [88.9]
KPG525-19 KFG525-19
5.25 [133.4]
KPG700-19 KFG700-19
7.00 [177.8]
KPG875-19 KFG875-19
8.75 [222.3]
KPG1050-19 KFG1050-19
10.50 [266.7]
Overall depth, including fasteners:
0.50 [12.7]
0.75 [19.1]
 

Dimensions, inches [mm], are for reference only and subject to change.

 

Filter-Grille
 

FILTERS: All KOOLTRONIC filters consist of a multi-layer grid of sturdy corrugated aluminum, securely held in a one-piece aluminum frame. Filters are required wherever air is drawn into an electronics enclosure or related cooling equipment to keep internal parts as clean as possible.
A non-drying adhesive coating traps a high percentage of particulate matter. These filters are reuseable, they may be washed and recoated with the appropriate filter recoating adhesive. Replacements are available for those which become damaged or otherwise non-serviceable.

FILTER RECOATING ADHESIVE: This compound is a superior product for recoating filters after washing. The adhesive penetrates dirt layers to keep the filter surface tacky for longer effective performance between washings. Part No. A-16.

 

ADAPTERS: (Set of two): These extend the width of any 19-inch [482.6mm] Packaged Blower, Packaged Fan or Rack-Mounted Air Conditioner to permit mounting in a cabinet designed for 24-inch [609.6mm] units. The EIA-notched adapters are covered by a plate of mirror-finish stainless steel to match Kooltronic Standard Grilles.

These adapters are non-structural. Therefore, Packaged Blowers and Rack-Mounted Air Conditioners must be supported at the rear, due to their weight. For Packaged Fans KP500 and KP875.

 
Model  
Mirror
 Finish
Brushed
 Finish
Height
KA24-3M KA24-3
3.50 [88.9]
KA24-5M KA24-5
5.25 [133.4]
KA24-7M KA24-7
7.00 [177.8]
KA24-8M KA24-8
8.75 [222.3]
KA24-10M KA24-10
10.50 [266.7]

Dimensions, inches [mm], are for reference only and subject to change.

   

AUTOMATIC SPEED CONTROL: The Kooltronic Fan and Blower Automatic Speed Control (Part Number KSC100) is a solid state "smart" controller packaged in a NEMA 1 type enclosure for remote mounting. The allowable input power supply range is 95 to 250 Volts, 47 to 63 Hz. It is furnished standard with an IEC 320 connector, a power supply fuse and a temperature sensor. Additional temperature sensors are optional.

The controller will operate single or multiple fans or blowers of compatible voltage and frequency up to a combined load of 6 Amps. The controller may be operated by either a control voltage signal of 0 to 10 VDC, a control current signal of 0 to 20 mA or one to three temperature sensors. With multiple temperature sensors the controller will respond to the highest sensed temperature.

The control circuit board is furnished with a terminal strip for field connecting the sensor and fan wires. A pressure type strain relief connector is furnished in the enclosure. If required by the installation or by code, this connector can be replaced with a 1/2-inch [12.7mm] trade size conduit connector.

A wide variety of control logic options can be field programmed into the controller by means of a board mounted DIP switch. These include fan idle or starting speed at 30%, 40%, 50% or 60% of supply voltage, fan on or off below the idle setting, control temperature setting of 86ºF (30ºC), 95ºF (35ºC), 104ºF (40ºC), 113ºF (45ºC), and temperature differential settings of 7ºF (4ºC) and 18ºF (10ºC). The selectable fan on/off feature is operative when the temperature(s) drop below the control temperature setting.

Consult factory for use with compatible Kooltronic fans or blowers.

DP33 Photo
DRAWINGS AND DIMENSIONS (click and drag to pan)
Dimensions, inches [mm], are for reference only and subject to change.
 

 

  
 
  Products - Services - News - Design Guide - Downloads - About Us - Manufacturing - Support - Contact Us We accept Visa and Mastercard We accept Company Purchase Orders
 
  © 1996- 2012 Kooltronic, Inc. - All rights reserved. - Terms of Use